Bouffalo ISP Protocol V1: Difference between revisions

From OpenBouffalo
Jump to navigation Jump to search
 
(4 intermediate revisions by the same user not shown)
Line 2: Line 2:


It is integrated in [[:Category:BL602_Series|BL602]], [[:Category:BL702_Series|BL702]], [[:Category:BL602_Series|BL808]] and [[:Category:BL602_Series|BL616]] series of chips, although, every series have some improvements to this protocol.
It is integrated in [[:Category:BL602_Series|BL602]], [[:Category:BL702_Series|BL702]], [[:Category:BL602_Series|BL808]] and [[:Category:BL602_Series|BL616]] series of chips, although, every series have some improvements to this protocol.
= List of supported interfaces per chip =


List of available interfaces for specific chips:
List of available interfaces for specific chips:
Line 64: Line 66:
}}
}}


Currently, there are two ways of getting into ISP mode, which we will describe in next sections:
Currently, there are two ways of getting into ISP mode, which we will describe in following sections:


== Via GPIO ==
== Via GPIO ==


Every chip using ISP Protocol V1 have ability to get into ISP mode by specifying voltage level on specific pin during boot time. This mechanism is implemented within BootROM code.
Every chip using ISP Protocol V1 have ability to get into ISP mode by specifying voltage level on specific pin during boot time. This mechanism is implemented within BootROM code.
BL602 as example, the boot pin needs to be pulled to it's according level (most of times HIGH) 0.1s before powering up the chip via PU_CHIP, and then boot pin needs to be kept at specified level at least 2ms after PU_CHIP get HIGH.
BL602 as example, the boot pin needs to be pulled to it's according level (most of times HIGH) 0.1s before powering up the chip via PU_CHIP, and then boot pin needs to be kept at specified level at least 2ms after PU_CHIP get HIGH.


Line 102: Line 105:
| IO2
| IO2
| High
| High
|  
| Multiplexed with JTAG? (not 100% confirmed)
|}
|}
== Via software ==
There are registers to reboot the chip and automatically launch ISP mode. (TODO)


= Handshake =
= Handshake =
= Run firmware =

Latest revision as of 06:19, 3 June 2023

This page describes Bouffalo ISP Protocol V1, which is ISP protocol used to run images, write images to Flash or program fuses via UART, USB, SDIO or JTAG.

It is integrated in BL602, BL702, BL808 and BL616 series of chips, although, every series have some improvements to this protocol.

List of supported interfaces per chip

List of available interfaces for specific chips:

Chip UART USB SDIO JTAG SD Card
BL602 Series Yes No Yes ? No
BL702 Series Yes Yes No ? No
BL808C Yes Broken ? ? Broken?
BL808D Yes N/A ? ? N/A
BL606P Yes ? ? ? N/A
BL616 Series Yes Yes ? ? ?

Getting into ISP/BootROM mode

Currently, there are two ways of getting into ISP mode, which we will describe in following sections:

Via GPIO

Every chip using ISP Protocol V1 have ability to get into ISP mode by specifying voltage level on specific pin during boot time. This mechanism is implemented within BootROM code.

BL602 as example, the boot pin needs to be pulled to it's according level (most of times HIGH) 0.1s before powering up the chip via PU_CHIP, and then boot pin needs to be kept at specified level at least 2ms after PU_CHIP get HIGH.

Example hardware layout

Example is taken from BL602 Datasheet

Bl602 bootpin layout.png

Chip Pin ISP Mode when pin is Note
BL602 Series IO8 High
BL702 Series IO28 High
BL808 Series IO39 High Multiplexed with QSPI D3 pin
BL616 Series IO2 High Multiplexed with JTAG? (not 100% confirmed)

Via software

There are registers to reboot the chip and automatically launch ISP mode. (TODO)

Handshake

Run firmware